LubeCorp Logo

Call Us: 1-800-661-6100

GreenCut® Cutting Fluid


GreenCut Cutting Fluid Material Safety Data Sheet (MSDS)

Product:
LubeCorp GreenCut Cutting/Misting Fluid

Product Identifier:
Water/Chemical Mixture

Chemical Family:
Aqua

Common Use:
Water-based Cutting/Misting Fluid

T.D.G. Class:
Not Controlled

WHMIS Class:
Not Controlled

HMIS:
Health: 0
Flammability: 0
Physical hazard: 0
Personal protection: 0

Tariff Number (H.S./B.T.N. Code):
3402.12.50.00

Hazardous Ingredients / Components:
None

% by Weight:
None

Hazard:
None

Supplier:
LubeCorp Manufacturing Inc.
7023 5 Street SE
Calgary, AB T2H 2E4
Canada

Emergency Telephone No.'s:
1.403.250.8448
1.800.661.6100

Date Prepared:
May 1, 2009

GreenCut is recommended at 20:1 (Water:GreenCut) treat ratio.
Here calculated as a concentrated 2:1 treat ratio for safety measures to show lack of toxicity.


Toxicity Data LC50 LD50:

Ecotoxicity Classification = Practically Non-Toxic


LC50 - Acute Aquatic:
>1,000 mg/L (Rainbow Trout) "Practically Non-Toxic" (OECD 203)

EC50:
> 1,000 mg/L 3 hour Biodegradability (OECD 209) (ASTM D-5864)
"Absolutely Non-Toxic to Wastewater Treatment Plant Bacteria"

LD50 - Oral:
<20,000 mg/Kg (Rat)

LD50 - Dermal:
<10,000 mg/Kg (Rabbit)

Carcinogenicity:
The materials in this product are not carcinogenic.

Physical Data for Product:


PH:
8.4 - 9.6

Specific Gravity:
1.070 - 1.076

Pour Point:
-10°C

Solubility in Water:
(% by Weight)
100

Appearance:
Green/Transparent

Odor:
Clean, Lemony

Reactivity Data for Product:


Incompatibility:
(Materials to Avoid)
None known.

Hazardous Decomposition Products:
None produced on combustion.

Can Hazardous Polymerization Occur?:
Will not occur.

Fire and Explosion Hazard:


Flash Point (C.O.C.):
Non-flammable.

Flammable Limits in Air:
(% by Volume)
N/A

Fire Extinguishing Substances:
Foam, CO2, Dry Chemical, Water Fog

Special Fire-fighting Procedures:
Water or foam.. Use water spray to cool fire exposed containers. Water may be used to flush spills away from exposure.

Health Hazard Information for Product:


Emergency and First Aid Procedures:


Inhalation:
Non Toxic. Remove to fresh air. Additional first aid treatment is not ordinarily required.

Ingestion:
Non Toxic. Drink several glasses of water. Call physician if needed.

Eyes:
Flush eyes with water. If irritation persists consult Physician.

Skin:
Remove contaminated clothing and wash skin and clothing with soap and water.

Spill or Leak Procedures for Product:

For small spills, clean up with absorbent material. Collect material in suitable and properly labeled open containers. For large spills, dike and pump into suitable and properly labeled containers.

Waste Disposal Method:

This product is fully biodegradable in a biological waste water treatment plant. All disposal methods must be in compliance with Federal, State/Provincial and local laws and regulations, and are the sole responsibility of the waste generator.

Special Protection Information for Product:


Ventilation Requirements:

General room ventilation should be adequate at ambient or elevated temperatures or in covered equipment.

Respiratory Protection:

None required.

Eye Protection:

Glasses or goggles may be worn to protect eyes.

Other Protection:

None required.

Regulatory Information:

The information herein is presented in good faith and believed to be accurate as of the effective date shown above. However, no warranty, express or implied is given. Regulatory requirements are subject to change and may differ from one location to another; it is the buyer's responsibility to ensure that its activities comply with federal, state/provincial, and local laws.

References Used to Complete MSDS:

Primary Supplier MSDS. Laboratory test results and analysis in conjunction with LubeCorp's experience and handling with this product. Contact MSDS co-ordinator, LubeCorp Manufacturing Inc.

End of MSDS.